NEWS CENTER
Here are the structural characteristics of the snow-plowing sanitation brush and the use of skills
Release time:
2022-07-28
Here are the structural characteristics of the snow-plowing sanitation brush and the use of skills
Here are the structural characteristics of the snow-plowing sanitation brush and the use of skills
1. The snow-removal sanitation brush is truncated conical, the bristles are mounted on the disk, also known as the disk brush, in order to clean the edge of the place, the conical brushes are mounted on both sides of the equipment, also known as the side brushes, in order to sweep the garbage from the side to the main brush on the sweeping path, the axle of the snow-removal sanitation brush is tilted at a certain angle with the ground.
2. Cylindrical snow-removal sanitation brush by the brush core, bristles and bristles fixed in the core of the components, usually, bristles into bundles along the brush core of the cylindrical surface of the dense arrangement of snow brush commonly used bristles steel wire, crushed flat bamboo strips, synthetic fibers, etc. Information, steel wire has a high abrasion resistance.
3. The belt brush consists of two roller chains, two driving sprockets and guide wheels and a toothed belt, brush area, cleaning the ground ability, but the complex structure of the snow brush is rarely used.
What materials are needed for sanitation brushes?
As the sanitation brush in the production of the principle of spiral sweeping, the tobacco leaves fall when the brush is stuck inside, easy to cause material blockage, but the soft brush can not clean the belt, the hard brush will damage the belt and increase the conveying resistance, sanitation brush bonding process using the materials and processes can not guarantee that it will not fall off, bonded hairs fall off when it will fall into the tobacco leaves, the tobacco leaves through the re-baker after baking, melting on the surface of the tobacco leaves or mixing with the tobacco leaves to The formation of impurities mixed into the tobacco will also affect the inner quality of the tobacco.
After the sanitation brush is used for later treatment, it should be treated separately from different sanitation brushes according to the different paints used.
1. Oil-based varnish.
2. Water-based and emulsion paints.
Because these paints are soluble in water, so after each operation, sanitation brushes should be carefully cleaned with water, and then shade-dried, not clean, the roots of the afternoon theater will be simple and firm, and the next time it is not good to use.
3. Oily cement
Scrape off the paint on the sanitation brush with a bamboo knife, soak the sanitation brush in non-drying oil, if often used, can be put into the water after use, however, if possible, it is better to put in non-drying oil.
4. Purple Gum Varnish and Synthetic Resin
Both should be cleaned with thinner, and when you want to continue to use it, you should put the sanitary brush in a sealed container or a bottle with a lid, and in such a container, put a cloth ball soaked with thinner thorns to prevent the sanitary brush from drying out.
What are the processing techniques for road sweeping sanitation brushes?
Hot-dip galvanizing, pickling, rolling brush, color coating and other lightweight production lines in the road sweeper processing occupies an important position in the steel industry, the production process is mainly spiral winding, internal assembly welding and spiral block brush assembly, brush wire is usually made of nylon or abrasive nylon with a diameter of 0.5 nylon, the rollers in the use of the cycle of the position, which consists of a single brush assembly, the key, the brush roller shaft and the overall brush roller assembly form the end plate.
Sanitation brush consists of a single brush, the combination is pressed on the brush roller shaft, the two ends of the fixed key and plate, nylon bristles as a whole on the outer circumference of the rotation of the utility model structure is simple, reasonably designed, long service life, can be in the effective length of the brush roller shaft to increase the amount of about 10% of a single brush set installation, so that the filler brush brush bristle density is high, to improve the quality of the cleaning, the overall brush roller of the nylon roller assembly of the outer surface is the overall trimming and polished to improve the balance of the brush roll and extend its service life.
Today, I will first explain to you here, if you need sanitation brush customization and procurement, you can contact our manufacturers.
Mobile：
Wechat/Whatsapp:
E-mail:
Address:
4th Floor, B area, Two Brushes Maker Space, Yuantan, Anqing, Anhui, China
Online Message
If you have any product related questions, please feel free to contact us!
Copyright © 2025 Starshine New Materials Technology Co., Ltd.